top of page

Load Cell Problems: Symptoms, Tests, and When to Replace

Cody
2 days ago
8 min read



When a scale starts misbehaving, the symptom is what you see: the reading drifts, jumps around, won't zero, or disappears entirely. The cause is less obvious. It can be the load cell — but it can just as easily be the cable, the indicator, the junction box, or the installation itself.

This page works symptom-first. Find what your scale is doing, see the likely causes, and jump to the exact test in our step-by-step testing guide that confirms it: How to Test a Load Cell: A Step-by-Step Guide. If a test does condemn the cell, the second half of this page covers the repair-or-replace decision, what drives the cost of a replacement, and how to match a new cell that actually fits your system.




Before You Blame the Load Cell


The testing guide makes this point in its FAQ: indicators, junction boxes, damaged cables, mechanical binding, and calibration issues can all produce the same symptoms as a failed load cell. That is why the guide starts where it does — Step 1: Check Excitation Voltage. If the indicator is not supplying excitation voltage, the load cell cannot be the problem, no matter what the display is doing.


Work through the symptom index below, run the confirming test, and let the result — not the symptom alone — make the call.


Symptom Index


Readings drift


The displayed weight slowly wanders, or the output will not settle at a steady value.


Likely causes: internal damage to the cell — including bridge damage from a lightning strike or power surge, which the guide's FAQ notes can leave a cell with unstable output; moisture intrusion in the cable or connections; a failing strain gauge.


Confirming tests: Step 2: Check the Load Cell Output (Millivolts) — a healthy cell's output is stable and does not drift significantly, so watch the millivolt reading over time rather than taking a single snapshot. Then Step 6: Inspect the Cable for moisture intrusion and corrosion. If the output is still unstable, Step 4: Compare Resistance to the Manufacturer's Specifications checks for internal damage.


Erratic or unstable readings


The reading jumps, flickers, or changes even though the load on the scale has not changed.


Likely causes: loose terminals or a damaged cable; mechanical binding or another installation problem; internal cell damage. As Step 3: Apply Weight and Watch the Millivolt Output puts it, output that changes erratically means the load cell, wiring, or mechanical installation may be faulty — all three are on the table.


Confirming tests: Step 3 to see the erratic behavior under applied weight, Step 6: Inspect the Cable for cuts, pinched wires, and loose terminals, and Step 2 to check output stability.


Zero shift


The scale's zero point has moved — the empty-scale reading sits higher or lower than it used to.

Likely causes: first, rule out the normal case. As Step 2 explains, an installed cell is always carrying the system's dead load — the deck, hopper, tank, or platform — so a no-load output somewhere between 0 and 5 mV is common and is not by itself a fault. A genuine zero shift means the no-load output has moved outside the manufacturer's stated zero-balance tolerance; zero balance is typically within ±1% of full-scale output. That points to internal damage.


Confirming tests: Step 2: Check the Load Cell Output (Millivolts), comparing your no-load reading against the specific model's zero-balance spec. If it is out of tolerance, Step 4 and Step 5: Cross-Check the Bridge check for the internal damage behind it.


Won't zero


The indicator will not return to zero, or will not hold zero between weighings.


Likely causes: a zero balance that has moved out of tolerance; mechanical binding; a damaged cable — the guide notes a damaged cable can produce the same symptoms as a failed load cell; or a calibration issue rather than a hardware failure at all.


Confirming tests: Step 2 for the no-load output against the model's tolerance, and Step 6: Inspect the Cable. If both check out, Step 4 compares the cell's resistance against its datasheet.


No output


The cell produces no signal at all.


Likely causes: work from the outside in. If there is no excitation voltage reaching the cell, the problem is the indicator, wiring, or power supply — not the cell. Beyond that: a cut or severed cable, rodent damage, or loose terminals; or an internal failure inside the cell.


Confirming tests: Step 1: Check Excitation Voltage first. Then Step 6: Inspect the Cable. If excitation is present and the cable is sound, Step 4 and Step 5: Cross-Check the Bridge — run with the cell disconnected, as the guide directs — will show an internal open or bridge failure.


Output doesn't respond to weight


There is a signal, but it does not increase when weight is applied.


Likely causes: Step 3 covers this case directly: if the millivolt output does not change when weight is added, the load cell, wiring, or mechanical installation may be faulty — including an installation problem that keeps the load from reaching the cell properly.


Confirming tests: Step 3: Apply Weight and Watch the Millivolt Output itself, then Step 6 for the wiring and Step 4 for the cell.


Repair or Replace? Reading Your Test Results


The tests separate into two piles: findings that point away from the load cell, and findings that point at it.


Fix the system, not the cell, when:


  • There is no excitation voltage. Step 1 puts the fault in the indicator, wiring, or power supply. The cell is not involved.

  • The cable inspection finds damage. Cuts in the jacket, pinched wires, moisture intrusion, corrosion, loose terminals, or rodent damage (Step 6) can all mimic a failed cell. Repair or replace the cable, correct the terminals, and retest before condemning the cell.

  • The problem is mechanical or calibration-related. Binding, a load that is not sitting on the cell correctly, or a calibration issue (the guide's FAQ lists all of these) are installation problems, not cell failures.


Replace the cell when:


  • Resistance readings differ significantly from the datasheet. The guide's FAQ reads that result as internal damage or a failed strain gauge (Step 4).

  • The bridge cross-check is unbalanced. One leg significantly different from the others in Step 5 points to an internal bridge failure.

  • Zero balance is outside the manufacturer's tolerance with excitation confirmed and the cable sound (Step 2).

  • Output is unstable or absent after excitation (Step 1) and the cable (Step 6) have both checked out.

  • There was a lightning strike or surge, followed by resistance readings that no longer match the datasheet — the guide's FAQ identifies this as bridge damage.


Two habits protect you from replacing a good cell. First, after any cable or wiring repair, repeat the output checks (Steps 2 and 3) before deciding — the repair may have been the whole problem. Second, in a multi-cell system, isolate each cell from the junction box before testing it. Measuring through the junction box without isolating the cell is one of the guide's listed Common Testing Mistakes, and it can hide which cell in the system is actually at fault.


What Drives the Cost of a Replacement Load Cell


There is no single "load cell price," because the part itself changes with the application. The main drivers:


  • Type and design. A compact single point cell for a bench scale and a hermetically sealed canister cell for a truck scale are very different constructions.

  • Capacity. Higher-capacity cells are larger, heavier builds, and capacity is one of the first things that moves a replacement's price.

  • Material. Aluminum, alloy steel, and stainless steel versions of similar cells sit at different price points, with stainless generally chosen — and priced — for washdown, outdoor, and corrosive service.

  • Sealing and IP rating. A basic potted cell, an IP67 cell, and a hermetically sealed IP69K cell for high-pressure washdown are built to different standards.

  • Manufacturer and model line. The brand and the specific model family the original cell came from.

  • Cable length and configuration. Longer cables and specific terminations are part of the part number, not an afterthought.

  • Mounting hardware. Some replacements reuse the mounts already on the scale; others need a new mounting assembly to install correctly and safely.

  • Certification. If your application requires a certified cell — for example, an NTEP-certified model for legal-for-trade use — that narrows the field of eligible replacements.


The part is also not the whole job: installation and recalibration after a replacement are part of the real cost of getting a scale back into service, and in a multi-cell system the remaining cells' condition is worth a look while the system is open.


Matching a Replacement: The Compatibility Checklist


An exact replacement — same manufacturer and model — is always the safest match. When that is not available, a substitute has to match the original on every point below. A cell that matches on most of them is not interchangeable; it is a near miss.


  • Capacity. Match the original's rated capacity. Remember the cell carries the dead load (deck, vessel, platform) plus the live load, so do not downsize.

  • Rated output (mV/V). The replacement's rated output should match the original's datasheet value. The indicator is calibrated expecting a specific signal at full capacity, and in a junction-box system every cell feeds one summed signal, so mismatched outputs make the system hard or impossible to calibrate evenly.

  • Excitation. The indicator supplies the excitation voltage — most supply between 5 and 15 VDC, per the testing guide — and the replacement must be rated to run on what your indicator provides.

  • Input and output resistance. Compare both against the original's datasheet; Step 4 of the testing guide measures them between the excitation leads and the signal leads respectively. Do not assume two similar-looking models share values — models within the same family can carry different specified resistances, so compare the exact part number's datasheet, not the family name.

  • Wiring and cable. Match the wire configuration, cable length, and termination of the original, and connect the new cell following its own datasheet wiring diagram rather than assuming the old cell's arrangement carries over.

  • Dimensions and mounting. Overall dimensions, mounting-hole pattern or footprint, and — on S-beam cells — the thread size all have to match the existing hardware and the cell being replaced.

  • Certification. If the scale is used in legal-for-trade service, the replacement generally needs the appropriate certification for that use — for example, NTEP certification for the specific model and capacity — and the complete scale system still has to be approved. Check the individual model's certification rather than assuming a family-wide approval.


Truck scale cells have their own documented path: the Truck Scale Load Cell Replacement & Cross-Reference Guide lists the replacement relationships manufacturers document, and its verification notes give the truck-specific checklist — part number on the cell coming out, capacity, dimensions, mounting and load cups or receivers, cable length and termination, output (mV/V), bridge resistance, and any legal-for-trade requirements for the installation.


Find Your Replacement


Start from the type of cell your scale uses:



Or browse all load cells. If the part number on your old cell does not match anything you find, send us the part number and scale model and we will identify the correct replacement before you order. If the label is missing or unreadable, clear photos of the cell, its mounting arrangement, and its cable or connector — along with dimensions, thread size, and capacity — can usually identify it.

 
 
 

Comments


bottom of page